Peripheral Control functions

Peripheral Control functions. More...

Functions
HAL_StatusTypeDef	HAL_TIM_OC_ConfigChannel (TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef *sConfig, uint32_t Channel)
	Initializes the TIM Output Compare Channels according to the specified parameters in the TIM_OC_InitTypeDef.
HAL_StatusTypeDef	HAL_TIM_IC_ConfigChannel (TIM_HandleTypeDef *htim, TIM_IC_InitTypeDef *sConfig, uint32_t Channel)
	Initializes the TIM Input Capture Channels according to the specified parameters in the TIM_IC_InitTypeDef.
HAL_StatusTypeDef	HAL_TIM_PWM_ConfigChannel (TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef *sConfig, uint32_t Channel)
	Initializes the TIM PWM channels according to the specified parameters in the TIM_OC_InitTypeDef.
HAL_StatusTypeDef	HAL_TIM_OnePulse_ConfigChannel (TIM_HandleTypeDef *htim, TIM_OnePulse_InitTypeDef *sConfig, uint32_t OutputChannel, uint32_t InputChannel)
	Initializes the TIM One Pulse Channels according to the specified parameters in the TIM_OnePulse_InitTypeDef.
HAL_StatusTypeDef	HAL_TIM_DMABurst_WriteStart (TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t *BurstBuffer, uint32_t BurstLength)
	Configure the DMA Burst to transfer Data from the memory to the TIM peripheral.
HAL_StatusTypeDef	HAL_TIM_DMABurst_WriteStop (TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc)
	Stops the TIM DMA Burst mode.
HAL_StatusTypeDef	HAL_TIM_DMABurst_ReadStart (TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t *BurstBuffer, uint32_t BurstLength)
	Configure the DMA Burst to transfer Data from the TIM peripheral to the memory.
HAL_StatusTypeDef	HAL_TIM_DMABurst_ReadStop (TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc)
	Stop the DMA burst reading.
HAL_StatusTypeDef	HAL_TIM_GenerateEvent (TIM_HandleTypeDef *htim, uint32_t EventSource)
	Generate a software event.
HAL_StatusTypeDef	HAL_TIM_ConfigOCrefClear (TIM_HandleTypeDef *htim, TIM_ClearInputConfigTypeDef *sClearInputConfig, uint32_t Channel)
	Configures the OCRef clear feature.
HAL_StatusTypeDef	HAL_TIM_ConfigClockSource (TIM_HandleTypeDef *htim, TIM_ClockConfigTypeDef *sClockSourceConfig)
	Configures the clock source to be used.
HAL_StatusTypeDef	HAL_TIM_ConfigTI1Input (TIM_HandleTypeDef *htim, uint32_t TI1_Selection)
	Selects the signal connected to the TI1 input: direct from CH1_input or a XOR combination between CH1_input, CH2_input & CH3_input.
HAL_StatusTypeDef	HAL_TIM_SlaveConfigSynchronization (TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef *sSlaveConfig)
	Configures the TIM in Slave mode.
HAL_StatusTypeDef	HAL_TIM_SlaveConfigSynchronization_IT (TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef *sSlaveConfig)
	Configures the TIM in Slave mode in interrupt mode.
uint32_t	HAL_TIM_ReadCapturedValue (TIM_HandleTypeDef *htim, uint32_t Channel)
	Read the captured value from Capture Compare unit.

---

Detailed Description

Peripheral Control functions.

  ==============================================================================
                   ##### Peripheral Control functions #####
  ==============================================================================
 [..]
   This section provides functions allowing to:
      (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode.
      (+) Configure External Clock source.
      (+) Configure Complementary channels, break features and dead time.
      (+) Configure Master and the Slave synchronization.
      (+) Configure the DMA Burst Mode.

---

Function Documentation

HAL_StatusTypeDef HAL_TIM_ConfigClockSource	(	TIM_HandleTypeDef *	htim,
		TIM_ClockConfigTypeDef *	sClockSourceConfig
	)

Configures the clock source to be used.

Parameters:

htim	TIM handle
sClockSourceConfig	pointer to a TIM_ClockConfigTypeDef structure that contains the clock source information for the TIM peripheral.

Return values:

HAL

status

Definition at line 4490 of file stm32l4xx_hal_tim.c.

References assert_param, TIM_ClockConfigTypeDef::ClockFilter, TIM_ClockConfigTypeDef::ClockPolarity, TIM_ClockConfigTypeDef::ClockPrescaler, TIM_ClockConfigTypeDef::ClockSource, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::Instance, IS_TIM_CLOCKFILTER, IS_TIM_CLOCKPOLARITY, IS_TIM_CLOCKPRESCALER, IS_TIM_CLOCKSOURCE, __TIM_HandleTypeDef::State, TIM_CLOCKSOURCE_ETRMODE1, TIM_CLOCKSOURCE_ETRMODE2, TIM_CLOCKSOURCE_INTERNAL, TIM_CLOCKSOURCE_ITR0, TIM_CLOCKSOURCE_ITR1, TIM_CLOCKSOURCE_ITR2, TIM_CLOCKSOURCE_ITR3, TIM_CLOCKSOURCE_TI1, TIM_CLOCKSOURCE_TI1ED, TIM_CLOCKSOURCE_TI2, TIM_ETR_SetConfig(), TIM_ITRx_SetConfig(), TIM_SLAVEMODE_EXTERNAL1, TIM_TI1_ConfigInputStage(), and TIM_TI2_ConfigInputStage().

HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear	(	TIM_HandleTypeDef *	htim,
		TIM_ClearInputConfigTypeDef *	sClearInputConfig,
		uint32_t	Channel
	)

Configures the OCRef clear feature.

Parameters:

htim	TIM handle
sClearInputConfig	pointer to a TIM_ClearInputConfigTypeDef structure that contains the OCREF clear feature and parameters for the TIM peripheral.
Channel	specifies the TIM Channel This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 TIM_CHANNEL_2: TIM Channel 2 TIM_CHANNEL_3: TIM Channel 3 TIM_CHANNEL_4: TIM Channel 4 TIM_CHANNEL_5: TIM Channel 5 TIM_CHANNEL_6: TIM Channel 6

Return values:

HAL

status

Definition at line 4337 of file stm32l4xx_hal_tim.c.

References assert_param, TIM_ClearInputConfigTypeDef::ClearInputFilter, TIM_ClearInputConfigTypeDef::ClearInputPolarity, TIM_ClearInputConfigTypeDef::ClearInputPrescaler, TIM_ClearInputConfigTypeDef::ClearInputSource, TIM_ClearInputConfigTypeDef::ClearInputState, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::Instance, IS_TIM_CLEARINPUT_FILTER, IS_TIM_CLEARINPUT_POLARITY, IS_TIM_CLEARINPUT_PRESCALER, IS_TIM_CLEARINPUT_SOURCE, __TIM_HandleTypeDef::State, TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_CHANNEL_4, TIM_CHANNEL_5, TIM_CHANNEL_6, TIM_CLEARINPUTSOURCE_ETR, TIM_CLEARINPUTSOURCE_NONE, TIM_CLEARINPUTSOURCE_OCREFCLR, and TIM_ETR_SetConfig().

HAL_StatusTypeDef HAL_TIM_ConfigTI1Input	(	TIM_HandleTypeDef *	htim,
		uint32_t	TI1_Selection
	)

Selects the signal connected to the TI1 input: direct from CH1_input or a XOR combination between CH1_input, CH2_input & CH3_input.

Parameters:

htim	TIM handle.
TI1_Selection	Indicate whether or not channel 1 is connected to the output of a XOR gate. This parameter can be one of the following values: TIM_TI1SELECTION_CH1: The TIMx_CH1 pin is connected to TI1 input TIM_TI1SELECTION_XORCOMBINATION: The TIMx_CH1, CH2 and CH3 pins are connected to the TI1 input (XOR combination)

Return values:

HAL

status

Definition at line 4646 of file stm32l4xx_hal_tim.c.

References assert_param, __TIM_HandleTypeDef::Instance, and IS_TIM_TI1SELECTION.

HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart	(	TIM_HandleTypeDef *	htim,
		uint32_t	BurstBaseAddress,
		uint32_t	BurstRequestSrc,
		uint32_t *	BurstBuffer,
		uint32_t	BurstLength
	)

Configure the DMA Burst to transfer Data from the TIM peripheral to the memory.

Parameters:

htim	TIM handle
BurstBaseAddress	TIM Base address from where the DMA will start the Data read This parameter can be one of the following values: TIM_DMABASE_CR1 TIM_DMABASE_CR2 TIM_DMABASE_SMCR TIM_DMABASE_DIER TIM_DMABASE_SR TIM_DMABASE_EGR TIM_DMABASE_CCMR1 TIM_DMABASE_CCMR2 TIM_DMABASE_CCER TIM_DMABASE_CNT TIM_DMABASE_PSC TIM_DMABASE_ARR TIM_DMABASE_RCR TIM_DMABASE_CCR1 TIM_DMABASE_CCR2 TIM_DMABASE_CCR3 TIM_DMABASE_CCR4 TIM_DMABASE_BDTR TIM_DMABASE_DCR
BurstRequestSrc	TIM DMA Request sources This parameter can be one of the following values: TIM_DMA_UPDATE: TIM update Interrupt source TIM_DMA_CC1: TIM Capture Compare 1 DMA source TIM_DMA_CC2: TIM Capture Compare 2 DMA source TIM_DMA_CC3: TIM Capture Compare 3 DMA source TIM_DMA_CC4: TIM Capture Compare 4 DMA source TIM_DMA_COM: TIM Commutation DMA source TIM_DMA_TRIGGER: TIM Trigger DMA source
BurstBuffer	The Buffer address.
BurstLength	DMA Burst length. This parameter can be one value between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS.

Return values:

HAL

status

Definition at line 4062 of file stm32l4xx_hal_tim.c.

References __HAL_TIM_ENABLE_DMA, assert_param, HAL_DMA_Start_IT(), HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::hdma, __TIM_HandleTypeDef::Instance, IS_TIM_DMA_BASE, IS_TIM_DMA_LENGTH, IS_TIM_DMA_SOURCE, __TIM_HandleTypeDef::State, TIM_DMA_CC1, TIM_DMA_CC2, TIM_DMA_CC3, TIM_DMA_CC4, TIM_DMA_COM, TIM_DMA_ID_CC1, TIM_DMA_ID_CC2, TIM_DMA_ID_CC3, TIM_DMA_ID_CC4, TIM_DMA_ID_COMMUTATION, TIM_DMA_ID_TRIGGER, TIM_DMA_ID_UPDATE, TIM_DMA_TRIGGER, TIM_DMA_UPDATE, TIM_DMACaptureCplt(), TIM_DMAError(), TIM_DMAPeriodElapsedCplt(), TIM_DMATriggerCplt(), TIMEx_DMACommutationCplt(), __DMA_HandleTypeDef::XferCpltCallback, and __DMA_HandleTypeDef::XferErrorCallback.

HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop	(	TIM_HandleTypeDef *	htim,
		uint32_t	BurstRequestSrc
	)

Stop the DMA burst reading.

Parameters:

htim	TIM handle
BurstRequestSrc	TIM DMA Request sources to disable.

Return values:

HAL

status

Definition at line 4219 of file stm32l4xx_hal_tim.c.

References __HAL_TIM_DISABLE_DMA, assert_param, HAL_DMA_Abort(), __TIM_HandleTypeDef::hdma, IS_TIM_DMA_SOURCE, TIM_DMA_CC1, TIM_DMA_CC2, TIM_DMA_CC3, TIM_DMA_CC4, TIM_DMA_COM, TIM_DMA_ID_CC1, TIM_DMA_ID_CC2, TIM_DMA_ID_CC3, TIM_DMA_ID_CC4, TIM_DMA_ID_COMMUTATION, TIM_DMA_ID_TRIGGER, TIM_DMA_ID_UPDATE, TIM_DMA_TRIGGER, and TIM_DMA_UPDATE.

HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart	(	TIM_HandleTypeDef *	htim,
		uint32_t	BurstBaseAddress,
		uint32_t	BurstRequestSrc,
		uint32_t *	BurstBuffer,
		uint32_t	BurstLength
	)

Configure the DMA Burst to transfer Data from the memory to the TIM peripheral.

Parameters:

htim	TIM handle
BurstBaseAddress	TIM Base address from where the DMA will start the Data write This parameter can be one of the following values: TIM_DMABASE_CR1 TIM_DMABASE_CR2 TIM_DMABASE_SMCR TIM_DMABASE_DIER TIM_DMABASE_SR TIM_DMABASE_EGR TIM_DMABASE_CCMR1 TIM_DMABASE_CCMR2 TIM_DMABASE_CCER TIM_DMABASE_CNT TIM_DMABASE_PSC TIM_DMABASE_ARR TIM_DMABASE_RCR TIM_DMABASE_CCR1 TIM_DMABASE_CCR2 TIM_DMABASE_CCR3 TIM_DMABASE_CCR4 TIM_DMABASE_BDTR TIM_DMABASE_DCR
BurstRequestSrc	TIM DMA Request sources This parameter can be one of the following values: TIM_DMA_UPDATE: TIM update Interrupt source TIM_DMA_CC1: TIM Capture Compare 1 DMA source TIM_DMA_CC2: TIM Capture Compare 2 DMA source TIM_DMA_CC3: TIM Capture Compare 3 DMA source TIM_DMA_CC4: TIM Capture Compare 4 DMA source TIM_DMA_COM: TIM Commutation DMA source TIM_DMA_TRIGGER: TIM Trigger DMA source
BurstBuffer	The Buffer address.
BurstLength	DMA Burst length. This parameter can be one value between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS.

Return values:

HAL

status

Definition at line 3810 of file stm32l4xx_hal_tim.c.

References __HAL_TIM_ENABLE_DMA, assert_param, HAL_DMA_Start_IT(), HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::hdma, __TIM_HandleTypeDef::Instance, IS_TIM_DMA_BASE, IS_TIM_DMA_LENGTH, IS_TIM_DMA_SOURCE, __TIM_HandleTypeDef::State, TIM_DMA_CC1, TIM_DMA_CC2, TIM_DMA_CC3, TIM_DMA_CC4, TIM_DMA_COM, TIM_DMA_ID_CC1, TIM_DMA_ID_CC2, TIM_DMA_ID_CC3, TIM_DMA_ID_CC4, TIM_DMA_ID_COMMUTATION, TIM_DMA_ID_TRIGGER, TIM_DMA_ID_UPDATE, TIM_DMA_TRIGGER, TIM_DMA_UPDATE, TIM_DMADelayPulseCplt(), TIM_DMAError(), TIM_DMAPeriodElapsedCplt(), TIM_DMATriggerCplt(), TIMEx_DMACommutationCplt(), __DMA_HandleTypeDef::XferCpltCallback, and __DMA_HandleTypeDef::XferErrorCallback.

HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop	(	TIM_HandleTypeDef *	htim,
		uint32_t	BurstRequestSrc
	)

Stops the TIM DMA Burst mode.

Parameters:

htim	TIM handle
BurstRequestSrc	TIM DMA Request sources to disable

Return values:

HAL

status

Definition at line 3966 of file stm32l4xx_hal_tim.c.

References __HAL_TIM_DISABLE_DMA, assert_param, HAL_DMA_Abort(), __TIM_HandleTypeDef::hdma, IS_TIM_DMA_SOURCE, TIM_DMA_CC1, TIM_DMA_CC2, TIM_DMA_CC3, TIM_DMA_CC4, TIM_DMA_COM, TIM_DMA_ID_CC1, TIM_DMA_ID_CC2, TIM_DMA_ID_CC3, TIM_DMA_ID_CC4, TIM_DMA_ID_COMMUTATION, TIM_DMA_ID_TRIGGER, TIM_DMA_ID_UPDATE, TIM_DMA_TRIGGER, and TIM_DMA_UPDATE.

HAL_StatusTypeDef HAL_TIM_GenerateEvent	(	TIM_HandleTypeDef *	htim,
		uint32_t	EventSource
	)

Generate a software event.

Parameters:

htim

TIM handle

EventSource

specifies the event source. This parameter can be one of the following values: TIM_EVENTSOURCE_UPDATE: Timer update Event source TIM_EVENTSOURCE_CC1: Timer Capture Compare 1 Event source TIM_EVENTSOURCE_CC2: Timer Capture Compare 2 Event source TIM_EVENTSOURCE_CC3: Timer Capture Compare 3 Event source TIM_EVENTSOURCE_CC4: Timer Capture Compare 4 Event source TIM_EVENTSOURCE_COM: Timer COM event source TIM_EVENTSOURCE_TRIGGER: Timer Trigger Event source TIM_EVENTSOURCE_BREAK: Timer Break event source TIM_EVENTSOURCE_BREAK2: Timer Break2 event source

Note:

Basic timers can only generate an update event.

TIM_EVENTSOURCE_COM is relevant only with advanced timer instances.

TIM_EVENTSOURCE_BREAK and TIM_EVENTSOURCE_BREAK2 are relevant only for timer instances supporting break input(s).

Return values:

HAL

status

Definition at line 4298 of file stm32l4xx_hal_tim.c.

References assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::Instance, IS_TIM_EVENT_SOURCE, and __TIM_HandleTypeDef::State.

HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel	(	TIM_HandleTypeDef *	htim,
		TIM_IC_InitTypeDef *	sConfig,
		uint32_t	Channel
	)

Initializes the TIM Input Capture Channels according to the specified parameters in the TIM_IC_InitTypeDef.

Parameters:

htim	TIM IC handle
sConfig	TIM Input Capture configuration structure
Channel	TIM Channel to configure This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 selected TIM_CHANNEL_2: TIM Channel 2 selected TIM_CHANNEL_3: TIM Channel 3 selected TIM_CHANNEL_4: TIM Channel 4 selected

Return values:

HAL

status

Definition at line 3428 of file stm32l4xx_hal_tim.c.

References assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, TIM_IC_InitTypeDef::ICFilter, TIM_IC_InitTypeDef::ICPolarity, TIM_IC_InitTypeDef::ICPrescaler, TIM_IC_InitTypeDef::ICSelection, __TIM_HandleTypeDef::Instance, IS_TIM_IC_FILTER, IS_TIM_IC_POLARITY, IS_TIM_IC_PRESCALER, IS_TIM_IC_SELECTION, __TIM_HandleTypeDef::State, TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_TI1_SetConfig(), TIM_TI2_SetConfig(), TIM_TI3_SetConfig(), and TIM_TI4_SetConfig().

HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel	(	TIM_HandleTypeDef *	htim,
		TIM_OC_InitTypeDef *	sConfig,
		uint32_t	Channel
	)

Initializes the TIM Output Compare Channels according to the specified parameters in the TIM_OC_InitTypeDef.

Parameters:

htim	TIM Output Compare handle
sConfig	TIM Output Compare configuration structure
Channel	TIM Channels to configure This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 selected TIM_CHANNEL_2: TIM Channel 2 selected TIM_CHANNEL_3: TIM Channel 3 selected TIM_CHANNEL_4: TIM Channel 4 selected TIM_CHANNEL_5: TIM Channel 5 selected TIM_CHANNEL_6: TIM Channel 6 selected

Return values:

HAL

status

Definition at line 3328 of file stm32l4xx_hal_tim.c.

References assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::Instance, IS_TIM_CHANNELS, IS_TIM_OC_MODE, IS_TIM_OC_POLARITY, TIM_OC_InitTypeDef::OCMode, TIM_OC_InitTypeDef::OCPolarity, __TIM_HandleTypeDef::State, TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_CHANNEL_4, TIM_CHANNEL_5, TIM_CHANNEL_6, TIM_OC1_SetConfig(), TIM_OC2_SetConfig(), TIM_OC3_SetConfig(), TIM_OC4_SetConfig(), TIM_OC5_SetConfig(), and TIM_OC6_SetConfig().

HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel	(	TIM_HandleTypeDef *	htim,
		TIM_OnePulse_InitTypeDef *	sConfig,
		uint32_t	OutputChannel,
		uint32_t	InputChannel
	)

Initializes the TIM One Pulse Channels according to the specified parameters in the TIM_OnePulse_InitTypeDef.

Parameters:

htim	TIM One Pulse handle
sConfig	TIM One Pulse configuration structure
OutputChannel	TIM output channel to configure This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 selected TIM_CHANNEL_2: TIM Channel 2 selected
InputChannel	TIM input Channel to configure This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 selected TIM_CHANNEL_2: TIM Channel 2 selected

Return values:

HAL

status

Definition at line 3672 of file stm32l4xx_hal_tim.c.

References assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, TIM_OnePulse_InitTypeDef::ICFilter, TIM_OnePulse_InitTypeDef::ICPolarity, TIM_OnePulse_InitTypeDef::ICSelection, __TIM_HandleTypeDef::Instance, IS_TIM_OPM_CHANNELS, TIM_OC_InitTypeDef::OCIdleState, TIM_OnePulse_InitTypeDef::OCIdleState, TIM_OC_InitTypeDef::OCMode, TIM_OnePulse_InitTypeDef::OCMode, TIM_OC_InitTypeDef::OCNIdleState, TIM_OnePulse_InitTypeDef::OCNIdleState, TIM_OC_InitTypeDef::OCNPolarity, TIM_OnePulse_InitTypeDef::OCNPolarity, TIM_OC_InitTypeDef::OCPolarity, TIM_OnePulse_InitTypeDef::OCPolarity, TIM_OC_InitTypeDef::Pulse, TIM_OnePulse_InitTypeDef::Pulse, __TIM_HandleTypeDef::State, TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_OC1_SetConfig(), TIM_OC2_SetConfig(), TIM_SLAVEMODE_TRIGGER, TIM_TI1_SetConfig(), TIM_TI2_SetConfig(), TIM_TS_TI1FP1, and TIM_TS_TI2FP2.

HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel	(	TIM_HandleTypeDef *	htim,
		TIM_OC_InitTypeDef *	sConfig,
		uint32_t	Channel
	)

Initializes the TIM PWM channels according to the specified parameters in the TIM_OC_InitTypeDef.

Parameters:

htim	TIM PWM handle
sConfig	TIM PWM configuration structure
Channel	TIM Channels to be configured This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 selected TIM_CHANNEL_2: TIM Channel 2 selected TIM_CHANNEL_3: TIM Channel 3 selected TIM_CHANNEL_4: TIM Channel 4 selected TIM_CHANNEL_5: TIM Channel 5 selected TIM_CHANNEL_6: TIM Channel 6 selected

Return values:

HAL

status

Definition at line 3527 of file stm32l4xx_hal_tim.c.

References assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::Instance, IS_TIM_CHANNELS, IS_TIM_FAST_STATE, IS_TIM_OC_POLARITY, IS_TIM_PWM_MODE, TIM_OC_InitTypeDef::OCFastMode, TIM_OC_InitTypeDef::OCMode, TIM_OC_InitTypeDef::OCPolarity, __TIM_HandleTypeDef::State, TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_CHANNEL_4, TIM_CHANNEL_5, TIM_CHANNEL_6, TIM_OC1_SetConfig(), TIM_OC2_SetConfig(), TIM_OC3_SetConfig(), TIM_OC4_SetConfig(), TIM_OC5_SetConfig(), and TIM_OC6_SetConfig().

uint32_t HAL_TIM_ReadCapturedValue	(	TIM_HandleTypeDef *	htim,
		uint32_t	Channel
	)

Read the captured value from Capture Compare unit.

Parameters:

htim	TIM handle.
Channel	TIM Channels to be enabled This parameter can be one of the following values: TIM_CHANNEL_1: TIM Channel 1 selected TIM_CHANNEL_2: TIM Channel 2 selected TIM_CHANNEL_3: TIM Channel 3 selected TIM_CHANNEL_4: TIM Channel 4 selected

Return values:

Captured

value

Definition at line 4751 of file stm32l4xx_hal_tim.c.

References assert_param, __TIM_HandleTypeDef::Instance, TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, and TIM_CHANNEL_4.

HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization	(	TIM_HandleTypeDef *	htim,
		TIM_SlaveConfigTypeDef *	sSlaveConfig
	)

Configures the TIM in Slave mode.

Parameters:

htim	TIM handle.
sSlaveConfig	pointer to a TIM_SlaveConfigTypeDef structure that contains the selected trigger (internal trigger input, filtered timer input or external trigger input) and the Slave mode (Disable, Reset, Gated, Trigger, External clock mode 1).

Return values:

HAL

status

Definition at line 4678 of file stm32l4xx_hal_tim.c.

References __HAL_TIM_DISABLE_DMA, __HAL_TIM_DISABLE_IT, assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, TIM_SlaveConfigTypeDef::InputTrigger, __TIM_HandleTypeDef::Instance, IS_TIM_SLAVE_MODE, IS_TIM_TRIGGER_SELECTION, TIM_SlaveConfigTypeDef::SlaveMode, __TIM_HandleTypeDef::State, TIM_DMA_TRIGGER, TIM_IT_TRIGGER, and TIM_SlaveTimer_SetConfig().

HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT	(	TIM_HandleTypeDef *	htim,
		TIM_SlaveConfigTypeDef *	sSlaveConfig
	)

Configures the TIM in Slave mode in interrupt mode.

Parameters:

htim	TIM handle.
sSlaveConfig	pointer to a TIM_SlaveConfigTypeDef structure that contains the selected trigger (internal trigger input, filtered timer input or external trigger input) and the Slave mode (Disable, Reset, Gated, Trigger, External clock mode 1).

Return values:

HAL

status

Definition at line 4713 of file stm32l4xx_hal_tim.c.

References __HAL_TIM_DISABLE_DMA, __HAL_TIM_ENABLE_IT, assert_param, HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, TIM_SlaveConfigTypeDef::InputTrigger, __TIM_HandleTypeDef::Instance, IS_TIM_SLAVE_MODE, IS_TIM_TRIGGER_SELECTION, TIM_SlaveConfigTypeDef::SlaveMode, __TIM_HandleTypeDef::State, TIM_DMA_TRIGGER, TIM_IT_TRIGGER, and TIM_SlaveTimer_SetConfig().