STM32L486xx HAL User Manual
|
Timer Complementary Output Compare functions. More...
Functions | |
HAL_StatusTypeDef | HAL_TIMEx_OCN_Start (TIM_HandleTypeDef *htim, uint32_t Channel) |
Starts the TIM Output Compare signal generation on the complementary output. | |
HAL_StatusTypeDef | HAL_TIMEx_OCN_Stop (TIM_HandleTypeDef *htim, uint32_t Channel) |
Stops the TIM Output Compare signal generation on the complementary output. | |
HAL_StatusTypeDef | HAL_TIMEx_OCN_Start_IT (TIM_HandleTypeDef *htim, uint32_t Channel) |
Starts the TIM Output Compare signal generation in interrupt mode on the complementary output. | |
HAL_StatusTypeDef | HAL_TIMEx_OCN_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel) |
Stops the TIM Output Compare signal generation in interrupt mode on the complementary output. | |
HAL_StatusTypeDef | HAL_TIMEx_OCN_Start_DMA (TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) |
Starts the TIM Output Compare signal generation in DMA mode on the complementary output. | |
HAL_StatusTypeDef | HAL_TIMEx_OCN_Stop_DMA (TIM_HandleTypeDef *htim, uint32_t Channel) |
Stops the TIM Output Compare signal generation in DMA mode on the complementary output. |
Timer Complementary Output Compare functions.
============================================================================== ##### Timer Complementary Output Compare functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Start the Complementary Output Compare/PWM. (+) Stop the Complementary Output Compare/PWM. (+) Start the Complementary Output Compare/PWM and enable interrupts. (+) Stop the Complementary Output Compare/PWM and disable interrupts. (+) Start the Complementary Output Compare/PWM and enable DMA transfers. (+) Stop the Complementary Output Compare/PWM and disable DMA transfers.
HAL_StatusTypeDef HAL_TIMEx_OCN_Start | ( | TIM_HandleTypeDef * | htim, |
uint32_t | Channel | ||
) |
Starts the TIM Output Compare signal generation on the complementary output.
htim | TIM Output Compare handle |
Channel | TIM Channel to be enabled This parameter can be one of the following values:
|
HAL | status |
Definition at line 515 of file stm32l4xx_hal_tim_ex.c.
References __HAL_TIM_ENABLE, __HAL_TIM_MOE_ENABLE, assert_param, __TIM_HandleTypeDef::Instance, IS_TIM_SLAVEMODE_TRIGGER_ENABLED, TIM_CCxN_ENABLE, and TIM_CCxNChannelCmd().
HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA | ( | TIM_HandleTypeDef * | htim, |
uint32_t | Channel, | ||
uint32_t * | pData, | ||
uint16_t | Length | ||
) |
Starts the TIM Output Compare signal generation in DMA mode on the complementary output.
htim | TIM Output Compare handle |
Channel | TIM Channel to be enabled This parameter can be one of the following values:
|
pData | The source Buffer address. |
Length | The length of data to be transferred from memory to TIM peripheral |
HAL | status |
Definition at line 705 of file stm32l4xx_hal_tim_ex.c.
References __HAL_TIM_ENABLE, __HAL_TIM_ENABLE_DMA, __HAL_TIM_MOE_ENABLE, assert_param, HAL_DMA_Start_IT(), HAL_TIM_STATE_BUSY, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::hdma, __TIM_HandleTypeDef::Instance, IS_TIM_SLAVEMODE_TRIGGER_ENABLED, __TIM_HandleTypeDef::State, TIM_CCxN_ENABLE, TIM_CCxNChannelCmd(), TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_DMA_CC1, TIM_DMA_CC2, TIM_DMA_CC3, TIM_DMA_ID_CC1, TIM_DMA_ID_CC2, TIM_DMA_ID_CC3, TIM_DMADelayPulseCplt(), TIM_DMAError(), __DMA_HandleTypeDef::XferCpltCallback, and __DMA_HandleTypeDef::XferErrorCallback.
HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT | ( | TIM_HandleTypeDef * | htim, |
uint32_t | Channel | ||
) |
Starts the TIM Output Compare signal generation in interrupt mode on the complementary output.
htim | TIM OC handle |
Channel | TIM Channel to be enabled This parameter can be one of the following values:
|
HAL | status |
Definition at line 576 of file stm32l4xx_hal_tim_ex.c.
References __HAL_TIM_ENABLE, __HAL_TIM_ENABLE_IT, __HAL_TIM_MOE_ENABLE, assert_param, __TIM_HandleTypeDef::Instance, IS_TIM_SLAVEMODE_TRIGGER_ENABLED, TIM_CCxN_ENABLE, TIM_CCxNChannelCmd(), TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_IT_BREAK, TIM_IT_CC1, TIM_IT_CC2, and TIM_IT_CC3.
HAL_StatusTypeDef HAL_TIMEx_OCN_Stop | ( | TIM_HandleTypeDef * | htim, |
uint32_t | Channel | ||
) |
Stops the TIM Output Compare signal generation on the complementary output.
htim | TIM handle |
Channel | TIM Channel to be disabled This parameter can be one of the following values:
|
HAL | status |
Definition at line 547 of file stm32l4xx_hal_tim_ex.c.
References __HAL_TIM_DISABLE, __HAL_TIM_MOE_DISABLE, assert_param, __TIM_HandleTypeDef::Instance, TIM_CCxN_DISABLE, and TIM_CCxNChannelCmd().
HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA | ( | TIM_HandleTypeDef * | htim, |
uint32_t | Channel | ||
) |
Stops the TIM Output Compare signal generation in DMA mode on the complementary output.
htim | TIM Output Compare handle |
Channel | TIM Channel to be disabled This parameter can be one of the following values:
|
HAL | status |
Definition at line 817 of file stm32l4xx_hal_tim_ex.c.
References __HAL_TIM_DISABLE, __HAL_TIM_DISABLE_DMA, __HAL_TIM_MOE_DISABLE, assert_param, HAL_TIM_STATE_READY, __TIM_HandleTypeDef::Instance, __TIM_HandleTypeDef::State, TIM_CCxN_DISABLE, TIM_CCxNChannelCmd(), TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_DMA_CC1, TIM_DMA_CC2, and TIM_DMA_CC3.
HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT | ( | TIM_HandleTypeDef * | htim, |
uint32_t | Channel | ||
) |
Stops the TIM Output Compare signal generation in interrupt mode on the complementary output.
htim | TIM Output Compare handle |
Channel | TIM Channel to be disabled This parameter can be one of the following values:
|
HAL | status |
Definition at line 639 of file stm32l4xx_hal_tim_ex.c.
References __HAL_TIM_DISABLE, __HAL_TIM_DISABLE_IT, __HAL_TIM_MOE_DISABLE, assert_param, __TIM_HandleTypeDef::Instance, TIM_CCxN_DISABLE, TIM_CCxNChannelCmd(), TIM_CHANNEL_1, TIM_CHANNEL_2, TIM_CHANNEL_3, TIM_IT_BREAK, TIM_IT_CC1, TIM_IT_CC2, and TIM_IT_CC3.