STM32L486xx HAL User Manual
|
#include <stm32l4xx_ll_i2c.h>
Data Fields | |
uint32_t | PeripheralMode |
uint32_t | Timing |
uint32_t | AnalogFilter |
uint32_t | DigitalFilter |
uint32_t | OwnAddress1 |
uint32_t | TypeAcknowledge |
uint32_t | OwnAddrSize |
Definition at line 83 of file stm32l4xx_ll_i2c.h.
uint32_t LL_I2C_InitTypeDef::AnalogFilter |
Enables or disables analog noise filter. This parameter can be a value of Analog Filter Selection
This feature can be modified afterwards using unitary functions LL_I2C_EnableAnalogFilter() or LL_I2C_DisableAnalogFilter().
Definition at line 96 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().
uint32_t LL_I2C_InitTypeDef::DigitalFilter |
Configures the digital noise filter. This parameter can be a number between Min_Data = 0x00 and Max_Data = 0x0F
This feature can be modified afterwards using unitary function LL_I2C_SetDigitalFilter().
Definition at line 101 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().
uint32_t LL_I2C_InitTypeDef::OwnAddress1 |
Specifies the device own address 1. This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF
This feature can be modified afterwards using unitary function LL_I2C_SetOwnAddress1().
Definition at line 106 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().
uint32_t LL_I2C_InitTypeDef::OwnAddrSize |
Specifies the device own address 1 size (7-bit or 10-bit). This parameter can be a value of Own Address 1 Length
This feature can be modified afterwards using unitary function LL_I2C_SetOwnAddress1().
Definition at line 116 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().
uint32_t LL_I2C_InitTypeDef::PeripheralMode |
Specifies the peripheral mode. This parameter can be a value of Peripheral Mode
This feature can be modified afterwards using unitary function LL_I2C_SetMode().
Definition at line 85 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().
uint32_t LL_I2C_InitTypeDef::Timing |
Specifies the SDA setup, hold time and the SCL high, low period values. This parameter must be set by referring to the STM32CubeMX Tool and the helper macro __LL_I2C_CONVERT_TIMINGS()
This feature can be modified afterwards using unitary function LL_I2C_SetTiming().
Definition at line 90 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().
uint32_t LL_I2C_InitTypeDef::TypeAcknowledge |
Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. This parameter can be a value of Acknowledge Generation
This feature can be modified afterwards using unitary function LL_I2C_AcknowledgeNextData().
Definition at line 111 of file stm32l4xx_ll_i2c.h.
Referenced by LL_I2C_Init(), and LL_I2C_StructInit().