RCC Extended MCOx Clock Config

Defines
#define	__HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__)   MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), ((__MCOCLKSOURCE__) | (__MCODIV__)))
	Macro to configure the MCO1 clock.
#define	__HAL_RCC_MCO2_CONFIG(__MCOCLKSOURCE__, __MCODIV__)   MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), ((__MCOCLKSOURCE__) | ((__MCODIV__) << 3U)));
	Macro to configure the MCO2 clock.

---

Define Documentation

#define __HAL_RCC_MCO1_CONFIG	(		__MCOCLKSOURCE__,
			__MCODIV__
	)		MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), ((__MCOCLKSOURCE__) | (__MCODIV__)))

Macro to configure the MCO1 clock.

Parameters:

__MCOCLKSOURCE__	specifies the MCO clock source. This parameter can be one of the following values: RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source
__MCODIV__	specifies the MCO clock prescaler. This parameter can be one of the following values: RCC_MCODIV_1: no division applied to MCOx clock RCC_MCODIV_2: division by 2 applied to MCOx clock RCC_MCODIV_3: division by 3 applied to MCOx clock RCC_MCODIV_4: division by 4 applied to MCOx clock RCC_MCODIV_5: division by 5 applied to MCOx clock

Definition at line 1136 of file stm32f4xx_hal_rcc.h.

#define __HAL_RCC_MCO2_CONFIG	(		__MCOCLKSOURCE__,
			__MCODIV__
	)		MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), ((__MCOCLKSOURCE__) | ((__MCODIV__) << 3U)));

Macro to configure the MCO2 clock.

Parameters:

__MCOCLKSOURCE__

specifies the MCO clock source. This parameter can be one of the following values: RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source

__MCODIV__

specifies the MCO clock prescaler. This parameter can be one of the following values: RCC_MCODIV_1: no division applied to MCOx clock RCC_MCODIV_2: division by 2 applied to MCOx clock RCC_MCODIV_3: division by 3 applied to MCOx clock RCC_MCODIV_4: division by 4 applied to MCOx clock RCC_MCODIV_5: division by 5 applied to MCOx clock

Note:

For STM32F410Rx devices, to output I2SCLK clock on MCO2, you should have at least one of the SPI clocks enabled (SPI1, SPI2 or SPI5).

Definition at line 1157 of file stm32f4xx_hal_rcc.h.