Defines
#define	__HAL_LCD_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_LCD_STATE_RESET)
	Reset LCD handle state.
#define	__HAL_LCD_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR, LCD_CR_LCDEN)
	Enable the LCD peripheral.
#define	__HAL_LCD_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR, LCD_CR_LCDEN)
	Disable the LCD peripheral.
#define	__HAL_LCD_HIGHDRIVER_ENABLE(__HANDLE__)
	Enable the low resistance divider.
#define	__HAL_LCD_HIGHDRIVER_DISABLE(__HANDLE__)
	Disable the low resistance divider.
#define	__HAL_LCD_VOLTAGE_BUFFER_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR, LCD_CR_BUFEN)
	Enable the voltage output buffer for higher driving capability.
#define	__HAL_LCD_VOLTAGE_BUFFER_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR, LCD_CR_BUFEN)
	Disable the voltage output buffer for higher driving capability.
#define	__HAL_LCD_PULSEONDURATION_CONFIG(__HANDLE__, __DURATION__)
	Configure the LCD pulse on duration.
#define	__HAL_LCD_DEADTIME_CONFIG(__HANDLE__, __DEADTIME__)
	Configure the LCD dead time.
#define	__HAL_LCD_CONTRAST_CONFIG(__HANDLE__, __CONTRAST__)
	Configure the LCD contrast.
#define	__HAL_LCD_BLINK_CONFIG(__HANDLE__, __BLINKMODE__, __BLINKFREQUENCY__)
	Configure the LCD Blink mode and Blink frequency.
#define	__HAL_LCD_ENABLE_IT(__HANDLE__, __INTERRUPT__)
	Enable the specified LCD interrupt.
#define	__HAL_LCD_DISABLE_IT(__HANDLE__, __INTERRUPT__)
	Disable the specified LCD interrupt.
#define	__HAL_LCD_GET_IT_SOURCE(__HANDLE__, __IT__) (((__HANDLE__)->Instance->FCR) & (__IT__))
	Check whether the specified LCD interrupt source is enabled or not.
#define	__HAL_LCD_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
	Check whether the specified LCD flag is set or not.
#define	__HAL_LCD_CLEAR_FLAG(__HANDLE__, __FLAG__) WRITE_REG((__HANDLE__)->Instance->CLR, (__FLAG__))
	Clear the specified LCD pending flag.

Define Documentation

#define __HAL_LCD_BLINK_CONFIG	(	__HANDLE__,
		__BLINKMODE__,
		__BLINKFREQUENCY__
	)

Value:

do {                                                                    \
                MODIFY_REG((__HANDLE__)->Instance->FCR, (LCD_FCR_BLINKF | LCD_FCR_BLINK), ((__BLINKMODE__) | (__BLINKFREQUENCY__))); \
                LCD_WaitForSynchro(__HANDLE__);                                       \
              } while(0)

Configure the LCD Blink mode and Blink frequency.

Parameters:

__HANDLE__,:	specifies the LCD Handle.
__BLINKMODE__,:	specifies the LCD blink mode. This parameter can be one of the following values: LCD_BLINKMODE_OFF: Blink disabled LCD_BLINKMODE_SEG0_COM0: Blink enabled on SEG[0], COM[0] (1 pixel) LCD_BLINKMODE_SEG0_ALLCOM: Blink enabled on SEG[0], all COM (up to 8 pixels according to the programmed duty) LCD_BLINKMODE_ALLSEG_ALLCOM: Blink enabled on all SEG and all COM (all pixels)
__BLINKFREQUENCY__,:	specifies the LCD blink frequency. LCD_BLINKFREQUENCY_DIV8: The Blink frequency = fLcd/8 LCD_BLINKFREQUENCY_DIV16: The Blink frequency = fLcd/16 LCD_BLINKFREQUENCY_DIV32: The Blink frequency = fLcd/32 LCD_BLINKFREQUENCY_DIV64: The Blink frequency = fLcd/64 LCD_BLINKFREQUENCY_DIV128: The Blink frequency = fLcd/128 LCD_BLINKFREQUENCY_DIV256: The Blink frequency = fLcd/256 LCD_BLINKFREQUENCY_DIV512: The Blink frequency = fLcd/512 LCD_BLINKFREQUENCY_DIV1024: The Blink frequency = fLcd/1024

Return values:

None

Definition at line 511 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_CLEAR_FLAG	(	__HANDLE__,
		__FLAG__
	)	WRITE_REG((__HANDLE__)->Instance->CLR, (__FLAG__))

Clear the specified LCD pending flag.

Parameters:

__HANDLE__,:	specifies the LCD Handle.
__FLAG__,:	specifies the flag to clear. This parameter can be any combination of the following values: LCD_FLAG_SOF: Start of Frame Interrupt LCD_FLAG_UDD: Update Display Done Interrupt

Return values:

None

Definition at line 588 of file stm32l4xx_hal_lcd.h.

Referenced by HAL_LCD_UpdateDisplayRequest().

#define __HAL_LCD_CONTRAST_CONFIG	(	__HANDLE__,
		__CONTRAST__
	)

Value:

do {                                                                    \
                MODIFY_REG((__HANDLE__)->Instance->FCR, LCD_FCR_CC, (__CONTRAST__));  \
                LCD_WaitForSynchro(__HANDLE__);                                       \
              } while(0)

Configure the LCD contrast.

Parameters:

__HANDLE__,: specifies the LCD Handle.

__CONTRAST__,:

specifies the LCD Contrast. This parameter can be one of the following values:

LCD_CONTRASTLEVEL_0: Maximum Voltage = 2.60V
LCD_CONTRASTLEVEL_1: Maximum Voltage = 2.73V
LCD_CONTRASTLEVEL_2: Maximum Voltage = 2.86V
LCD_CONTRASTLEVEL_3: Maximum Voltage = 2.99V
LCD_CONTRASTLEVEL_4: Maximum Voltage = 3.12V
LCD_CONTRASTLEVEL_5: Maximum Voltage = 3.25V
LCD_CONTRASTLEVEL_6: Maximum Voltage = 3.38V
LCD_CONTRASTLEVEL_7: Maximum Voltage = 3.51V

Return values:

None

Definition at line 483 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_DEADTIME_CONFIG	(	__HANDLE__,
		__DEADTIME__
	)

Value:

do {                                                                     \
                    MODIFY_REG((__HANDLE__)->Instance->FCR, LCD_FCR_DEAD, (__DEADTIME__)); \
                    LCD_WaitForSynchro(__HANDLE__);                                        \
                  } while(0)

Configure the LCD dead time.

Parameters:

__HANDLE__,: specifies the LCD Handle.

__DEADTIME__,:

specifies the LCD dead time. This parameter can be one of the following values:

LCD_DEADTIME_0: No dead Time
LCD_DEADTIME_1: One Phase between different couple of Frame
LCD_DEADTIME_2: Two Phase between different couple of Frame
LCD_DEADTIME_3: Three Phase between different couple of Frame
LCD_DEADTIME_4: Four Phase between different couple of Frame
LCD_DEADTIME_5: Five Phase between different couple of Frame
LCD_DEADTIME_6: Six Phase between different couple of Frame
LCD_DEADTIME_7: Seven Phase between different couple of Frame

Return values:

None

Definition at line 462 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_DISABLE ( __HANDLE__ ) CLEAR_BIT((__HANDLE__)->Instance->CR, LCD_CR_LCDEN)

Disable the LCD peripheral.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Return values:

None

Definition at line 386 of file stm32l4xx_hal_lcd.h.

Referenced by HAL_LCD_Init().

#define __HAL_LCD_DISABLE_IT	(	__HANDLE__,
		__INTERRUPT__
	)

Value:

do {                                                       \
                    CLEAR_BIT((__HANDLE__)->Instance->FCR, (__INTERRUPT__)); \
                    LCD_WaitForSynchro(__HANDLE__);                          \
                  } while(0)

Disable the specified LCD interrupt.

Parameters:

__HANDLE__,:	specifies the LCD Handle.
__INTERRUPT__,:	specifies the LCD interrupt source to be disabled. This parameter can be one of the following values: LCD_IT_SOF: Start of Frame Interrupt LCD_IT_UDD: Update Display Done Interrupt

Return values:

None

Definition at line 539 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_ENABLE ( __HANDLE__ ) SET_BIT((__HANDLE__)->Instance->CR, LCD_CR_LCDEN)

Enable the LCD peripheral.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Return values:

None

Definition at line 380 of file stm32l4xx_hal_lcd.h.

Referenced by HAL_LCD_Init().

#define __HAL_LCD_ENABLE_IT	(	__HANDLE__,
		__INTERRUPT__
	)

Value:

do {                                                      \
                    SET_BIT((__HANDLE__)->Instance->FCR, (__INTERRUPT__));  \
                    LCD_WaitForSynchro(__HANDLE__);                         \
                  } while(0)

Enable the specified LCD interrupt.

Parameters:

__HANDLE__,:	specifies the LCD Handle.
__INTERRUPT__,:	specifies the LCD interrupt source to be enabled. This parameter can be one of the following values: LCD_IT_SOF: Start of Frame Interrupt LCD_IT_UDD: Update Display Done Interrupt

Return values:

None

Definition at line 525 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_GET_FLAG	(	__HANDLE__,
		__FLAG__
	)	(((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))

Check whether the specified LCD flag is set or not.

Parameters:

__HANDLE__,:	specifies the LCD Handle.
__FLAG__,:	specifies the flag to check. This parameter can be one of the following values: LCD_FLAG_ENS: LCD Enabled flag. It indicates the LCD controller status.

Note:

The ENS bit is set immediately when the LCDEN bit in the LCD_CR goes from 0 to 1. On deactivation it reflects the real status of LCD so it becomes 0 at the end of the last displayed frame.

LCD_FLAG_SOF: Start of Frame flag. This flag is set by hardware at the beginning of a new frame, at the same time as the display data is updated.
LCD_FLAG_UDR: Update Display Request flag.
LCD_FLAG_UDD: Update Display Done flag.
LCD_FLAG_RDY: Step_up converter Ready flag. It indicates the status of the step-up converter.
LCD_FLAG_FCRSF: LCD Frame Control Register Synchronization Flag. This flag is set by hardware each time the LCD_FCR register is updated in the LCDCLK domain.

Return values:

The	new state of __FLAG__ (TRUE or FALSE).

Definition at line 578 of file stm32l4xx_hal_lcd.h.

Referenced by HAL_LCD_Clear(), HAL_LCD_Init(), HAL_LCD_UpdateDisplayRequest(), HAL_LCD_Write(), and LCD_WaitForSynchro().

#define __HAL_LCD_GET_IT_SOURCE	(	__HANDLE__,
		__IT__
	)	(((__HANDLE__)->Instance->FCR) & (__IT__))

Check whether the specified LCD interrupt source is enabled or not.

Parameters:

__HANDLE__,:	specifies the LCD Handle.
__IT__,:	specifies the LCD interrupt source to check. This parameter can be one of the following values: LCD_IT_SOF: Start of Frame Interrupt LCD_IT_UDD: Update Display Done Interrupt.

Note:: If the device is in STOP mode (PCLK not provided) UDD will not generate an interrupt even if UDDIE = 1. If the display is not enabled the UDD interrupt will never occur.

Return values:

The	state of __IT__ (TRUE or FALSE).

Definition at line 556 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_HIGHDRIVER_DISABLE ( __HANDLE__ )

Value:

do {                                                  \
                    CLEAR_BIT((__HANDLE__)->Instance->FCR, LCD_FCR_HD); \
                    LCD_WaitForSynchro(__HANDLE__);                     \
                  } while(0)

Disable the low resistance divider.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Return values:

None

Definition at line 407 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_HIGHDRIVER_ENABLE ( __HANDLE__ )

Value:

do {                                                \
                    SET_BIT((__HANDLE__)->Instance->FCR, LCD_FCR_HD); \
                    LCD_WaitForSynchro(__HANDLE__);                   \
                  } while(0)

Enable the low resistance divider.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Note:: Displays with high internal resistance may need a longer drive time to achieve satisfactory contrast. This function is useful in this case if some additional power consumption can be tolerated.; When this mode is enabled, the PulseOn Duration (PON) have to be programmed to 1/CK_PS (LCD_PULSEONDURATION_1).

Return values:

None

Definition at line 397 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_PULSEONDURATION_CONFIG	(	__HANDLE__,
		__DURATION__
	)

Value:

do {                                                                    \
                    MODIFY_REG((__HANDLE__)->Instance->FCR, LCD_FCR_PON, (__DURATION__)); \
                    LCD_WaitForSynchro(__HANDLE__);                                       \
                  } while(0)

Configure the LCD pulse on duration.

Parameters:

__HANDLE__,: specifies the LCD Handle.

__DURATION__,:

specifies the LCD pulse on duration in terms of CK_PS (prescaled LCD clock period) pulses. This parameter can be one of the following values:

LCD_PULSEONDURATION_0: 0 pulse
LCD_PULSEONDURATION_1: Pulse ON duration = 1/CK_PS
LCD_PULSEONDURATION_2: Pulse ON duration = 2/CK_PS
LCD_PULSEONDURATION_3: Pulse ON duration = 3/CK_PS
LCD_PULSEONDURATION_4: Pulse ON duration = 4/CK_PS
LCD_PULSEONDURATION_5: Pulse ON duration = 5/CK_PS
LCD_PULSEONDURATION_6: Pulse ON duration = 6/CK_PS
LCD_PULSEONDURATION_7: Pulse ON duration = 7/CK_PS

Return values:

None

Definition at line 441 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_RESET_HANDLE_STATE ( __HANDLE__ ) ((__HANDLE__)->State = HAL_LCD_STATE_RESET)

Reset LCD handle state.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Return values:

None

Definition at line 374 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_VOLTAGE_BUFFER_DISABLE ( __HANDLE__ ) CLEAR_BIT((__HANDLE__)->Instance->CR, LCD_CR_BUFEN)

Disable the voltage output buffer for higher driving capability.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Return values:

None

Definition at line 423 of file stm32l4xx_hal_lcd.h.

#define __HAL_LCD_VOLTAGE_BUFFER_ENABLE ( __HANDLE__ ) SET_BIT((__HANDLE__)->Instance->CR, LCD_CR_BUFEN)

Enable the voltage output buffer for higher driving capability.

Parameters:

__HANDLE__,: specifies the LCD Handle.

Return values:

None

Definition at line 417 of file stm32l4xx_hal_lcd.h.

Defines

Define Documentation