SYSCFG driver modules.
More...
Modules |
| SYSCFG_Exported_Constants |
| SYSCFG_Private_Functions |
Defines |
#define | SYSCFG_OFFSET (SYSCFG_BASE - PERIPH_BASE) |
#define | PMC_OFFSET (SYSCFG_OFFSET + 0x04) |
#define | MII_RMII_SEL_BitNumber ((uint8_t)0x17) |
#define | PMC_MII_RMII_SEL_BB (PERIPH_BB_BASE + (PMC_OFFSET * 32) + (MII_RMII_SEL_BitNumber * 4)) |
#define | CMPCR_OFFSET (SYSCFG_OFFSET + 0x20) |
#define | CMP_PD_BitNumber ((uint8_t)0x00) |
#define | CMPCR_CMP_PD_BB (PERIPH_BB_BASE + (CMPCR_OFFSET * 32) + (CMP_PD_BitNumber * 4)) |
Functions |
void | SYSCFG_DeInit (void) |
| Deinitializes the Alternate Functions (remap and EXTI configuration) registers to their default reset values.
|
void | SYSCFG_MemoryRemapConfig (uint8_t SYSCFG_MemoryRemap) |
| Changes the mapping of the specified pin.
|
void | SYSCFG_EXTILineConfig (uint8_t EXTI_PortSourceGPIOx, uint8_t EXTI_PinSourcex) |
| Selects the GPIO pin used as EXTI Line.
|
void | SYSCFG_ETH_MediaInterfaceConfig (uint32_t SYSCFG_ETH_MediaInterface) |
| Selects the ETHERNET media interface.
|
void | SYSCFG_CompensationCellCmd (FunctionalState NewState) |
| Enables or disables the I/O Compensation Cell.
|
FlagStatus | SYSCFG_GetCompensationCellStatus (void) |
| Checks whether the I/O Compensation Cell ready flag is set or not.
|
Detailed Description
SYSCFG driver modules.
Function Documentation
void SYSCFG_CompensationCellCmd |
( |
FunctionalState |
NewState |
) |
|
Enables or disables the I/O Compensation Cell.
- Note:
- The I/O compensation cell can be used only when the device supply voltage ranges from 2.4 to 3.6 V.
- Parameters:
-
| NewState,: | new state of the I/O Compensation Cell. This parameter can be one of the following values:
- ENABLE: I/O compensation cell enabled
- DISABLE: I/O compensation cell power-down mode
|
- Return values:
-
void SYSCFG_DeInit |
( |
void |
|
) |
|
Deinitializes the Alternate Functions (remap and EXTI configuration) registers to their default reset values.
- Parameters:
-
- Return values:
-
void SYSCFG_ETH_MediaInterfaceConfig |
( |
uint32_t |
SYSCFG_ETH_MediaInterface |
) |
|
Selects the ETHERNET media interface.
- Parameters:
-
| SYSCFG_ETH_MediaInterface,: | specifies the Media Interface mode. This parameter can be one of the following values:
- SYSCFG_ETH_MediaInterface_MII: MII mode selected
- SYSCFG_ETH_MediaInterface_RMII: RMII mode selected
|
- Return values:
-
void SYSCFG_EXTILineConfig |
( |
uint8_t |
EXTI_PortSourceGPIOx, |
|
|
uint8_t |
EXTI_PinSourcex | |
|
) |
| | |
Selects the GPIO pin used as EXTI Line.
- Parameters:
-
| EXTI_PortSourceGPIOx | : selects the GPIO port to be used as source for EXTI lines where x can be (A..I). |
| EXTI_PinSourcex,: | specifies the EXTI line to be configured. This parameter can be EXTI_PinSourcex where x can be (0..15, except for EXTI_PortSourceGPIOI x can be (0..11). |
- Return values:
-
FlagStatus SYSCFG_GetCompensationCellStatus |
( |
void |
|
) |
|
Checks whether the I/O Compensation Cell ready flag is set or not.
- Parameters:
-
- Return values:
-
| The | new state of the I/O Compensation Cell ready flag (SET or RESET) |
void SYSCFG_MemoryRemapConfig |
( |
uint8_t |
SYSCFG_MemoryRemap |
) |
|
Changes the mapping of the specified pin.
- Parameters:
-
| SYSCFG_Memory,: | selects the memory remapping. This parameter can be one of the following values:
- SYSCFG_MemoryRemap_Flash: Main Flash memory mapped at 0x00000000
- SYSCFG_MemoryRemap_SystemFlash: System Flash memory mapped at 0x00000000
- SYSCFG_MemoryRemap_FSMC: FSMC (Bank1 (NOR/PSRAM 1 and 2) mapped at 0x00000000
- SYSCFG_MemoryRemap_SRAM: Embedded SRAM (112kB) mapped at 0x00000000
|
- Return values:
-