|
STM32F439xx HAL User Manual
|
Structure definition of ADC and regular group initialization. More...
#include <stm32f4xx_hal_adc.h>
Data Fields | |
| uint32_t | ClockPrescaler |
| uint32_t | Resolution |
| uint32_t | DataAlign |
| uint32_t | ScanConvMode |
| uint32_t | EOCSelection |
| uint32_t | ContinuousConvMode |
| uint32_t | NbrOfConversion |
| uint32_t | DiscontinuousConvMode |
| uint32_t | NbrOfDiscConversion |
| uint32_t | ExternalTrigConv |
| uint32_t | ExternalTrigConvEdge |
| uint32_t | DMAContinuousRequests |
Structure definition of ADC and regular group initialization.
Definition at line 73 of file stm32f4xx_hal_adc.h.
| uint32_t ADC_InitTypeDef::ClockPrescaler |
Select ADC clock prescaler. The clock is common for all the ADCs. This parameter can be a value of ADC Clock Prescaler
Definition at line 75 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), and HAL_ADC_Init().
| uint32_t ADC_InitTypeDef::ContinuousConvMode |
Specifies whether the conversion is performed in single mode (one conversion) or continuous mode for regular group, after the selected trigger occurred (software start or external trigger). This parameter can be set to ENABLE or DISABLE.
Definition at line 97 of file stm32f4xx_hal_adc.h.
Referenced by ADC_DMAConvCplt(), ADC_Init(), ADC_MultiModeDMAConvCplt(), HAL_ADC_Init(), HAL_ADC_IRQHandler(), HAL_ADC_PollForConversion(), HAL_ADC_Start(), HAL_ADC_Start_DMA(), HAL_ADC_Start_IT(), HAL_ADCEx_InjectedPollForConversion(), and HAL_ADCEx_MultiModeStart_DMA().
| uint32_t ADC_InitTypeDef::DataAlign |
Specifies ADC data alignment to right (MSB on register bit 11 and LSB on register bit 0) (default setting) or to left (if regular group: MSB on register bit 15 and LSB on register bit 4, if injected group (MSB kept as signed value due to potential negative value after offset application): MSB on register bit 14 and LSB on register bit 3). This parameter can be a value of ADC Data Align
Definition at line 80 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), and HAL_ADC_Init().
Specifies whether the conversions sequence of regular group is performed in Complete-sequence/Discontinuous-sequence (main sequence subdivided in successive parts). Discontinuous mode is used only if sequencer is enabled (parameter 'ScanConvMode'). If sequencer is disabled, this parameter is discarded. Discontinuous mode can be enabled only if continuous mode is disabled. If continuous mode is enabled, this parameter setting is discarded. This parameter can be set to ENABLE or DISABLE.
Definition at line 103 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), and HAL_ADC_Init().
Specifies whether the DMA requests are performed in one shot mode (DMA transfer stop when number of conversions is reached) or in Continuous mode (DMA transfer unlimited, whatever number of conversions). Note: In continuous mode, DMA must be configured in circular mode. Otherwise an overrun will be triggered when DMA buffer maximum pointer is reached. Note: This parameter must be modified when no conversion is on going on both regular and injected groups (ADC disabled, or ADC enabled without continuous mode or external trigger that could launch a conversion). This parameter can be set to ENABLE or DISABLE.
Definition at line 117 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), HAL_ADC_Init(), and HAL_ADCEx_MultiModeStart_DMA().
| uint32_t ADC_InitTypeDef::EOCSelection |
Specifies what EOC (End Of Conversion) flag is used for conversion by polling and interruption: end of conversion of each rank or complete sequence. This parameter can be a value of ADC EOC Selection. Note: For injected group, end of conversion (flag&IT) is raised only at the end of the sequence. Therefore, if end of conversion is set to end of each conversion, injected group should not be used with interruption (HAL_ADCEx_InjectedStart_IT) or polling (HAL_ADCEx_InjectedStart and HAL_ADCEx_InjectedPollForConversion). By the way, polling is still possible since driver will use an estimated timing for end of injected conversion. Note: If overrun feature is intended to be used, use ADC in mode 'interruption' (function HAL_ADC_Start_IT() ) with parameter EOCSelection set to end of each conversion or in mode 'transfer by DMA' (function HAL_ADC_Start_DMA()). If overrun feature is intended to be bypassed, use ADC in mode 'polling' or 'interruption' with parameter EOCSelection must be set to end of sequence
Definition at line 90 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), HAL_ADC_Init(), and HAL_ADC_IRQHandler().
| uint32_t ADC_InitTypeDef::ExternalTrigConv |
Selects the external event used to trigger the conversion start of regular group. If set to ADC_SOFTWARE_START, external triggers are disabled. If set to external trigger source, triggering is on event rising edge by default. This parameter can be a value of ADC External Trigger Source Regular
Definition at line 110 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), and HAL_ADC_Init().
Selects the external trigger edge of regular group. If trigger is set to ADC_SOFTWARE_START, this parameter is discarded. This parameter can be a value of ADC External Trigger Edge Regular
Definition at line 114 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), HAL_ADC_Init(), HAL_ADC_Start(), HAL_ADC_Start_DMA(), HAL_ADC_Start_IT(), and HAL_ADCEx_MultiModeStart_DMA().
| uint32_t ADC_InitTypeDef::NbrOfConversion |
Specifies the number of ranks that will be converted within the regular group sequencer. To use regular group sequencer and convert several ranks, parameter 'ScanConvMode' must be enabled. This parameter must be a number between Min_Data = 1 and Max_Data = 16.
Definition at line 100 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), HAL_ADC_Init(), and HAL_ADC_IRQHandler().
| uint32_t ADC_InitTypeDef::NbrOfDiscConversion |
Specifies the number of discontinuous conversions in which the main sequence of regular group (parameter NbrOfConversion) will be subdivided. If parameter 'DiscontinuousConvMode' is disabled, this parameter is discarded. This parameter must be a number between Min_Data = 1 and Max_Data = 8.
Definition at line 107 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init().
| uint32_t ADC_InitTypeDef::Resolution |
Configures the ADC resolution. This parameter can be a value of ADC Resolution
Definition at line 78 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), and HAL_ADC_Init().
| uint32_t ADC_InitTypeDef::ScanConvMode |
Configures the sequencer of regular and injected groups. This parameter can be associated to parameter 'DiscontinuousConvMode' to have main sequence subdivided in successive parts. If disabled: Conversion is performed in single mode (one channel converted, the one defined in rank 1). Parameters 'NbrOfConversion' and 'InjectedNbrOfConversion' are discarded (equivalent to set to 1). If enabled: Conversions are performed in sequence mode (multiple ranks defined by 'NbrOfConversion'/'InjectedNbrOfConversion' and each channel rank). Scan direction is upward: from rank1 to rank 'n'. This parameter can be set to ENABLE or DISABLE
Definition at line 83 of file stm32f4xx_hal_adc.h.
Referenced by ADC_Init(), and HAL_ADC_Init().
1.7.6.1