|
STM32F439xx HAL User Manual
|
00001 /** 00002 ****************************************************************************** 00003 * @file stm32f4xx_hal_conf_template.h 00004 * @author MCD Application Team 00005 * @brief HAL configuration template file. 00006 * This file should be copied to the application folder and renamed 00007 * to stm32f4xx_hal_conf.h. 00008 ****************************************************************************** 00009 * @attention 00010 * 00011 * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> 00012 * 00013 * Redistribution and use in source and binary forms, with or without modification, 00014 * are permitted provided that the following conditions are met: 00015 * 1. Redistributions of source code must retain the above copyright notice, 00016 * this list of conditions and the following disclaimer. 00017 * 2. Redistributions in binary form must reproduce the above copyright notice, 00018 * this list of conditions and the following disclaimer in the documentation 00019 * and/or other materials provided with the distribution. 00020 * 3. Neither the name of STMicroelectronics nor the names of its contributors 00021 * may be used to endorse or promote products derived from this software 00022 * without specific prior written permission. 00023 * 00024 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 00025 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 00026 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 00027 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE 00028 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 00029 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 00030 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 00031 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 00032 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 00033 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 00034 * 00035 ****************************************************************************** 00036 */ 00037 00038 /* Define to prevent recursive inclusion -------------------------------------*/ 00039 #ifndef __STM32F4xx_HAL_CONF_H 00040 #define __STM32F4xx_HAL_CONF_H 00041 00042 #ifdef __cplusplus 00043 extern "C" { 00044 #endif 00045 00046 /* Exported types ------------------------------------------------------------*/ 00047 /* Exported constants --------------------------------------------------------*/ 00048 00049 /* ########################## Module Selection ############################## */ 00050 /** 00051 * @brief This is the list of modules to be used in the HAL driver 00052 */ 00053 #define HAL_MODULE_ENABLED 00054 #define HAL_ADC_MODULE_ENABLED 00055 #define HAL_CAN_MODULE_ENABLED 00056 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ 00057 #define HAL_CRC_MODULE_ENABLED 00058 #define HAL_CEC_MODULE_ENABLED 00059 #define HAL_CRYP_MODULE_ENABLED 00060 #define HAL_DAC_MODULE_ENABLED 00061 #define HAL_DCMI_MODULE_ENABLED 00062 #define HAL_DMA_MODULE_ENABLED 00063 #define HAL_DMA2D_MODULE_ENABLED 00064 #define HAL_ETH_MODULE_ENABLED 00065 #define HAL_FLASH_MODULE_ENABLED 00066 #define HAL_NAND_MODULE_ENABLED 00067 #define HAL_NOR_MODULE_ENABLED 00068 #define HAL_PCCARD_MODULE_ENABLED 00069 #define HAL_SRAM_MODULE_ENABLED 00070 #define HAL_SDRAM_MODULE_ENABLED 00071 #define HAL_HASH_MODULE_ENABLED 00072 #define HAL_GPIO_MODULE_ENABLED 00073 #define HAL_I2C_MODULE_ENABLED 00074 #define HAL_I2S_MODULE_ENABLED 00075 #define HAL_IWDG_MODULE_ENABLED 00076 #define HAL_LTDC_MODULE_ENABLED 00077 #define HAL_DSI_MODULE_ENABLED 00078 #define HAL_PWR_MODULE_ENABLED 00079 #define HAL_QSPI_MODULE_ENABLED 00080 #define HAL_RCC_MODULE_ENABLED 00081 #define HAL_RNG_MODULE_ENABLED 00082 #define HAL_RTC_MODULE_ENABLED 00083 #define HAL_SAI_MODULE_ENABLED 00084 #define HAL_SD_MODULE_ENABLED 00085 #define HAL_SPI_MODULE_ENABLED 00086 #define HAL_TIM_MODULE_ENABLED 00087 #define HAL_UART_MODULE_ENABLED 00088 #define HAL_USART_MODULE_ENABLED 00089 #define HAL_IRDA_MODULE_ENABLED 00090 #define HAL_SMARTCARD_MODULE_ENABLED 00091 #define HAL_WWDG_MODULE_ENABLED 00092 #define HAL_CORTEX_MODULE_ENABLED 00093 #define HAL_PCD_MODULE_ENABLED 00094 #define HAL_HCD_MODULE_ENABLED 00095 #define HAL_FMPI2C_MODULE_ENABLED 00096 #define HAL_SPDIFRX_MODULE_ENABLED 00097 #define HAL_DFSDM_MODULE_ENABLED 00098 #define HAL_LPTIM_MODULE_ENABLED 00099 #define HAL_MMC_MODULE_ENABLED 00100 00101 /* ########################## HSE/HSI Values adaptation ##################### */ 00102 /** 00103 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 00104 * This value is used by the RCC HAL module to compute the system frequency 00105 * (when HSE is used as system clock source, directly or through the PLL). 00106 */ 00107 #if !defined (HSE_VALUE) 00108 #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ 00109 #endif /* HSE_VALUE */ 00110 00111 #if !defined (HSE_STARTUP_TIMEOUT) 00112 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 00113 #endif /* HSE_STARTUP_TIMEOUT */ 00114 00115 /** 00116 * @brief Internal High Speed oscillator (HSI) value. 00117 * This value is used by the RCC HAL module to compute the system frequency 00118 * (when HSI is used as system clock source, directly or through the PLL). 00119 */ 00120 #if !defined (HSI_VALUE) 00121 #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ 00122 #endif /* HSI_VALUE */ 00123 00124 /** 00125 * @brief Internal Low Speed oscillator (LSI) value. 00126 */ 00127 #if !defined (LSI_VALUE) 00128 #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ 00129 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 00130 The real value may vary depending on the variations 00131 in voltage and temperature. */ 00132 /** 00133 * @brief External Low Speed oscillator (LSE) value. 00134 */ 00135 #if !defined (LSE_VALUE) 00136 #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ 00137 #endif /* LSE_VALUE */ 00138 00139 #if !defined (LSE_STARTUP_TIMEOUT) 00140 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 00141 #endif /* LSE_STARTUP_TIMEOUT */ 00142 00143 /** 00144 * @brief External clock source for I2S peripheral 00145 * This value is used by the I2S HAL module to compute the I2S clock source 00146 * frequency, this source is inserted directly through I2S_CKIN pad. 00147 */ 00148 #if !defined (EXTERNAL_CLOCK_VALUE) 00149 #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ 00150 #endif /* EXTERNAL_CLOCK_VALUE */ 00151 00152 /* Tip: To avoid modifying this file each time you need to use different HSE, 00153 === you can define the HSE value in your toolchain compiler preprocessor. */ 00154 00155 /* ########################### System Configuration ######################### */ 00156 /** 00157 * @brief This is the HAL system configuration section 00158 */ 00159 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 00160 #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ 00161 #define USE_RTOS 0U 00162 #define PREFETCH_ENABLE 1U 00163 #define INSTRUCTION_CACHE_ENABLE 1U 00164 #define DATA_CACHE_ENABLE 1U 00165 00166 /* ########################## Assert Selection ############################## */ 00167 /** 00168 * @brief Uncomment the line below to expanse the "assert_param" macro in the 00169 * HAL drivers code 00170 */ 00171 /* #define USE_FULL_ASSERT 1U */ 00172 00173 /* ################## Ethernet peripheral configuration ##################### */ 00174 00175 /* Section 1 : Ethernet peripheral configuration */ 00176 00177 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 00178 #define MAC_ADDR0 2U 00179 #define MAC_ADDR1 0U 00180 #define MAC_ADDR2 0U 00181 #define MAC_ADDR3 0U 00182 #define MAC_ADDR4 0U 00183 #define MAC_ADDR5 0U 00184 00185 /* Definition of the Ethernet driver buffers size and count */ 00186 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 00187 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 00188 #define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 00189 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 00190 00191 /* Section 2: PHY configuration section */ 00192 00193 /* DP83848 PHY Address*/ 00194 #define DP83848_PHY_ADDRESS 0x01U 00195 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 00196 #define PHY_RESET_DELAY 0x000000FFU 00197 /* PHY Configuration delay */ 00198 #define PHY_CONFIG_DELAY 0x00000FFFU 00199 00200 #define PHY_READ_TO 0x0000FFFFU 00201 #define PHY_WRITE_TO 0x0000FFFFU 00202 00203 /* Section 3: Common PHY Registers */ 00204 00205 #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ 00206 #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ 00207 00208 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 00209 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 00210 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 00211 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 00212 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 00213 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 00214 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 00215 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 00216 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 00217 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 00218 00219 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 00220 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 00221 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 00222 00223 /* Section 4: Extended PHY Registers */ 00224 00225 #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ 00226 #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ 00227 #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ 00228 00229 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 00230 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 00231 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 00232 00233 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 00234 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 00235 00236 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 00237 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 00238 00239 /* ################## SPI peripheral configuration ########################## */ 00240 00241 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 00242 * Activated: CRC code is present inside driver 00243 * Deactivated: CRC code cleaned from driver 00244 */ 00245 00246 #define USE_SPI_CRC 1U 00247 00248 /* Includes ------------------------------------------------------------------*/ 00249 /** 00250 * @brief Include module's header file 00251 */ 00252 00253 #ifdef HAL_RCC_MODULE_ENABLED 00254 #include "stm32f4xx_hal_rcc.h" 00255 #endif /* HAL_RCC_MODULE_ENABLED */ 00256 00257 #ifdef HAL_GPIO_MODULE_ENABLED 00258 #include "stm32f4xx_hal_gpio.h" 00259 #endif /* HAL_GPIO_MODULE_ENABLED */ 00260 00261 #ifdef HAL_DMA_MODULE_ENABLED 00262 #include "stm32f4xx_hal_dma.h" 00263 #endif /* HAL_DMA_MODULE_ENABLED */ 00264 00265 #ifdef HAL_CORTEX_MODULE_ENABLED 00266 #include "stm32f4xx_hal_cortex.h" 00267 #endif /* HAL_CORTEX_MODULE_ENABLED */ 00268 00269 #ifdef HAL_ADC_MODULE_ENABLED 00270 #include "stm32f4xx_hal_adc.h" 00271 #endif /* HAL_ADC_MODULE_ENABLED */ 00272 00273 #ifdef HAL_CAN_MODULE_ENABLED 00274 #include "stm32f4xx_hal_can.h" 00275 #endif /* HAL_CAN_MODULE_ENABLED */ 00276 00277 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 00278 #include "stm32f4xx_hal_can_legacy.h" 00279 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 00280 00281 #ifdef HAL_CRC_MODULE_ENABLED 00282 #include "stm32f4xx_hal_crc.h" 00283 #endif /* HAL_CRC_MODULE_ENABLED */ 00284 00285 #ifdef HAL_CRYP_MODULE_ENABLED 00286 #include "stm32f4xx_hal_cryp.h" 00287 #endif /* HAL_CRYP_MODULE_ENABLED */ 00288 00289 #ifdef HAL_DMA2D_MODULE_ENABLED 00290 #include "stm32f4xx_hal_dma2d.h" 00291 #endif /* HAL_DMA2D_MODULE_ENABLED */ 00292 00293 #ifdef HAL_DAC_MODULE_ENABLED 00294 #include "stm32f4xx_hal_dac.h" 00295 #endif /* HAL_DAC_MODULE_ENABLED */ 00296 00297 #ifdef HAL_DCMI_MODULE_ENABLED 00298 #include "stm32f4xx_hal_dcmi.h" 00299 #endif /* HAL_DCMI_MODULE_ENABLED */ 00300 00301 #ifdef HAL_ETH_MODULE_ENABLED 00302 #include "stm32f4xx_hal_eth.h" 00303 #endif /* HAL_ETH_MODULE_ENABLED */ 00304 00305 #ifdef HAL_FLASH_MODULE_ENABLED 00306 #include "stm32f4xx_hal_flash.h" 00307 #endif /* HAL_FLASH_MODULE_ENABLED */ 00308 00309 #ifdef HAL_SRAM_MODULE_ENABLED 00310 #include "stm32f4xx_hal_sram.h" 00311 #endif /* HAL_SRAM_MODULE_ENABLED */ 00312 00313 #ifdef HAL_NOR_MODULE_ENABLED 00314 #include "stm32f4xx_hal_nor.h" 00315 #endif /* HAL_NOR_MODULE_ENABLED */ 00316 00317 #ifdef HAL_NAND_MODULE_ENABLED 00318 #include "stm32f4xx_hal_nand.h" 00319 #endif /* HAL_NAND_MODULE_ENABLED */ 00320 00321 #ifdef HAL_PCCARD_MODULE_ENABLED 00322 #include "stm32f4xx_hal_pccard.h" 00323 #endif /* HAL_PCCARD_MODULE_ENABLED */ 00324 00325 #ifdef HAL_SDRAM_MODULE_ENABLED 00326 #include "stm32f4xx_hal_sdram.h" 00327 #endif /* HAL_SDRAM_MODULE_ENABLED */ 00328 00329 #ifdef HAL_HASH_MODULE_ENABLED 00330 #include "stm32f4xx_hal_hash.h" 00331 #endif /* HAL_HASH_MODULE_ENABLED */ 00332 00333 #ifdef HAL_I2C_MODULE_ENABLED 00334 #include "stm32f4xx_hal_i2c.h" 00335 #endif /* HAL_I2C_MODULE_ENABLED */ 00336 00337 #ifdef HAL_I2S_MODULE_ENABLED 00338 #include "stm32f4xx_hal_i2s.h" 00339 #endif /* HAL_I2S_MODULE_ENABLED */ 00340 00341 #ifdef HAL_IWDG_MODULE_ENABLED 00342 #include "stm32f4xx_hal_iwdg.h" 00343 #endif /* HAL_IWDG_MODULE_ENABLED */ 00344 00345 #ifdef HAL_LTDC_MODULE_ENABLED 00346 #include "stm32f4xx_hal_ltdc.h" 00347 #endif /* HAL_LTDC_MODULE_ENABLED */ 00348 00349 #ifdef HAL_PWR_MODULE_ENABLED 00350 #include "stm32f4xx_hal_pwr.h" 00351 #endif /* HAL_PWR_MODULE_ENABLED */ 00352 00353 #ifdef HAL_RNG_MODULE_ENABLED 00354 #include "stm32f4xx_hal_rng.h" 00355 #endif /* HAL_RNG_MODULE_ENABLED */ 00356 00357 #ifdef HAL_RTC_MODULE_ENABLED 00358 #include "stm32f4xx_hal_rtc.h" 00359 #endif /* HAL_RTC_MODULE_ENABLED */ 00360 00361 #ifdef HAL_SAI_MODULE_ENABLED 00362 #include "stm32f4xx_hal_sai.h" 00363 #endif /* HAL_SAI_MODULE_ENABLED */ 00364 00365 #ifdef HAL_SD_MODULE_ENABLED 00366 #include "stm32f4xx_hal_sd.h" 00367 #endif /* HAL_SD_MODULE_ENABLED */ 00368 00369 #ifdef HAL_SPI_MODULE_ENABLED 00370 #include "stm32f4xx_hal_spi.h" 00371 #endif /* HAL_SPI_MODULE_ENABLED */ 00372 00373 #ifdef HAL_TIM_MODULE_ENABLED 00374 #include "stm32f4xx_hal_tim.h" 00375 #endif /* HAL_TIM_MODULE_ENABLED */ 00376 00377 #ifdef HAL_UART_MODULE_ENABLED 00378 #include "stm32f4xx_hal_uart.h" 00379 #endif /* HAL_UART_MODULE_ENABLED */ 00380 00381 #ifdef HAL_USART_MODULE_ENABLED 00382 #include "stm32f4xx_hal_usart.h" 00383 #endif /* HAL_USART_MODULE_ENABLED */ 00384 00385 #ifdef HAL_IRDA_MODULE_ENABLED 00386 #include "stm32f4xx_hal_irda.h" 00387 #endif /* HAL_IRDA_MODULE_ENABLED */ 00388 00389 #ifdef HAL_SMARTCARD_MODULE_ENABLED 00390 #include "stm32f4xx_hal_smartcard.h" 00391 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 00392 00393 #ifdef HAL_WWDG_MODULE_ENABLED 00394 #include "stm32f4xx_hal_wwdg.h" 00395 #endif /* HAL_WWDG_MODULE_ENABLED */ 00396 00397 #ifdef HAL_PCD_MODULE_ENABLED 00398 #include "stm32f4xx_hal_pcd.h" 00399 #endif /* HAL_PCD_MODULE_ENABLED */ 00400 00401 #ifdef HAL_HCD_MODULE_ENABLED 00402 #include "stm32f4xx_hal_hcd.h" 00403 #endif /* HAL_HCD_MODULE_ENABLED */ 00404 00405 #ifdef HAL_DSI_MODULE_ENABLED 00406 #include "stm32f4xx_hal_dsi.h" 00407 #endif /* HAL_DSI_MODULE_ENABLED */ 00408 00409 #ifdef HAL_QSPI_MODULE_ENABLED 00410 #include "stm32f4xx_hal_qspi.h" 00411 #endif /* HAL_QSPI_MODULE_ENABLED */ 00412 00413 #ifdef HAL_CEC_MODULE_ENABLED 00414 #include "stm32f4xx_hal_cec.h" 00415 #endif /* HAL_CEC_MODULE_ENABLED */ 00416 00417 #ifdef HAL_FMPI2C_MODULE_ENABLED 00418 #include "stm32f4xx_hal_fmpi2c.h" 00419 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 00420 00421 #ifdef HAL_SPDIFRX_MODULE_ENABLED 00422 #include "stm32f4xx_hal_spdifrx.h" 00423 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 00424 00425 #ifdef HAL_DFSDM_MODULE_ENABLED 00426 #include "stm32f4xx_hal_dfsdm.h" 00427 #endif /* HAL_DFSDM_MODULE_ENABLED */ 00428 00429 #ifdef HAL_LPTIM_MODULE_ENABLED 00430 #include "stm32f4xx_hal_lptim.h" 00431 #endif /* HAL_LPTIM_MODULE_ENABLED */ 00432 00433 #ifdef HAL_MMC_MODULE_ENABLED 00434 #include "stm32f4xx_hal_mmc.h" 00435 #endif /* HAL_MMC_MODULE_ENABLED */ 00436 00437 /* Exported macro ------------------------------------------------------------*/ 00438 #ifdef USE_FULL_ASSERT 00439 /** 00440 * @brief The assert_param macro is used for function's parameters check. 00441 * @param expr If expr is false, it calls assert_failed function 00442 * which reports the name of the source file and the source 00443 * line number of the call that failed. 00444 * If expr is true, it returns no value. 00445 * @retval None 00446 */ 00447 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 00448 /* Exported functions ------------------------------------------------------- */ 00449 void assert_failed(uint8_t* file, uint32_t line); 00450 #else 00451 #define assert_param(expr) ((void)0U) 00452 #endif /* USE_FULL_ASSERT */ 00453 00454 00455 #ifdef __cplusplus 00456 } 00457 #endif 00458 00459 #endif /* __STM32F4xx_HAL_CONF_H */ 00460 00461 00462 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
1.7.6.1